2017 Raptor Rear Bumper Removal

2017 Raptor Rear Bumper Removal

2017-ford-raptor-supercrew-blue-rear
 
 

"I'm looking to remove my rear bumper off my Raptor and was wondering how to get it off. Can someone let me know how to do it or is there a video of how to do it? Thanks!"

Since we get this question asked so many times, we have made you a step by step install guide that anybody can use regardless of experience. With that being said, follow these 10 easy steps for a safe removal:

Preparation

  • Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
  • Please reading through this entire guide before performing removal.
  • You will need the following tools:
    • T40 Torx Socket
 
 

How do you remove the 2017 Raptor rear bumper

  1. Unplug the electrical connector on the back of your trailer light plug, then remove the plug by pushing in the two tabs and pulling it out the front of the bumper. (Fig A)
     
    2017-ford-raptor-rear-bumper-removal-fig-a
     
     
  2. Take off your license plate.
  3. Remove your license plate lights from their housing.
  4. Remove the parking sensors (x4) from their outer mounting rings. Simply spread the two tabs on the back of the mounting ring to allow the sensors to push out the back of the ring. Leave the mounting rings in the bumper for now. (Fig B)
     
    2017-ford-raptor-rear-oem-bumper-removal-fig-b
     
     
  5. Carefully pull the plastic center piece of the bumper off. There are no tools required for this step, it pulls off by hand. (Fig C)
     
    2017-ford-raptor-stock-bumper-removal-fig-c
     
     
  6. Using a T40 Torx Bit, remove the bolts (x5) holding on each metal side piece. (Fig D)
     
    2017-ford-raptor-oem-rear-bumper-removal-fig-d
     
     
  7. Remove the plastic clips (that hold the parking sensor harness in place) from the metal bumper ends, then remove the metal bumper ends from the truck. (Fig E)
     
    2017-ford-raptor-stock-bumper-removal-guide-fig-e
     
     
  8. Remove the parking sensor mounting rings from the OEM bumper. Do this by pressing in the two tabs on the back of the ring and pushing them out the front of the bumper.
  9. Remove the license plate light housings from the OEM bumper. Do this by pressing in the two tabs on the back of the housings and pushing them out the front of the bumper.
  10. Prepare to install your new ADD 2017 Ford Raptor aftermarket bumper.
 
 
ford raptor rear bumpers
 
 

Questions? Comments? Concerns? Feel free to give us a call and talk to one of our 2017 Ford Raptor experts at (480) 671-0820. Once you have the rear Front Bumper installed, complete the look with our other 2017 Ford Raptor parts & accessories.

 

Please note, comments must be approved before they are published

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Beyond the Bumper: Part 2 - Welding/Quality Control
In Part 1 of "Beyond the Bumper" we featured our laser and bend department, where the bumper manufacturing process begins! In this episode, we take you behind the scenes into our welding and quality control departments, crucial stages in the...
The 2025 Ram 1500 RHO: The TRX Successor
The off-roading world is in anticipation as the 2025 Ram 1500 RHO prepares to make its debut, succeeding the RAM TRX. The TRX, known for its 702-horsepower supercharged V-8, has been an icon among off-road enthusiasts over the past couple of...
Beyond the Bumper: Part 1 - Laser | Bend
Welcome to "Beyond the Bumper," a new series brought to you by Addictive Desert Designs in Chandler, Arizona. Part 1 of this multi-part series features our laser and bend department, where the bumper manufacturing process begins! What starts as a...